As the horizontal sunshine and southward vertical sunshine in Taiwan will affect the heat load of the exterior structure of the building, this scheme uses daylighting skylights with sunshade panels for overall design, so as to reduce internal air conditioning energy consumption and improve environmental quality. The sunshade system takes the structure as the branch and the glass as the leaf, symbolizing the light of regeneration and hope spilling into the interior space of the building, and the natural breath spreads and infiltrates from the four floors above ground to the third floor underground by the light of the sky. The top horizontal glass surface uses 50% light transmittance porcelain mesh glass to block direct sunlight and reduce the energy consumption of air conditioning in the building.
There are many parts of automobile interior decoration system, and the total value of bicycles is large. The automobile interior decoration system includes many subsystems, such as dashboard system, door guard system, ceiling system, seat system, post guard system, sunshade system and so on. According to the annual reports of listed companies such as Xinquan, Daimei and Tiancheng controls in 2020, the bicycle value of the automobile interior decoration system is about 8927 yuan, of which the car seat assembly, instrument panel assembly, top cabinet assembly and door assembly account for the highest proportion, accounting for about 75% of the total. Each car factory usually has a large automobile interior decoration team to complete a lot of engineering work related to the interior decoration.
First, the applicable extension width is 3, which uses a mechanical device and a crank arm device system. Under the action of spring, it can also be used for ceiling installation, light steel keel and other hard wall installation, brick wall motor control, the following is the awning fabric introduction. 00 meters, manual crank control through different transmission systems. The whole crank arm group is realized by an arm block, which can be adjusted in parallel with any precision of ~ 70 degrees. The characteristic of the 00-meter, half-box curved arm awning is that the sunshade fabric can be incorporated into the hood. Bolts and screws are made of high-quality stainless steel, applicable length is 6, can be applied to concrete, produce telescopic tension, infrared remote control and wind and rain sensor control, the structural frame adopts degree space aluminum. Wood. The common glass with good shading performance is endothermic glass, heat reflection glass, low radiation glass.
The interior of a car includes single or laminated organic materials for parts in the cab and passenger compartment The car interior material combustion instrument developed and produced by Beijing Xinsheng Zhuo Rui Technology Co., Ltd. can be tested in accordance with the GB8410 national standard, including seat cushion, seat back, seat cover, seat belt, headrest, handrail, movable folding roof, all interior linings (including door inner guard, front guard, side guard, rear guard, roof lining, etc.), dashboard, sundries, etc. Indoor shelf panels (including rear windowsill panels), curtains, floor coverings, sunshades, wheel hood coverings, engine hood coverings, fillers and buffers used to absorb collision energy during a crash.
The technical proposal adopted by the utility model for solving its technical problems is that a sunshade picnic heat preservation package comprises a package body, the top of the package body is provided with a circle opening and a cover connected with the opening through a zipper, two symmetrical straps are arranged on both sides of the package body, and an integrated plastic skeleton is arranged on the side wall and the bottom of the package body. The plastic skeleton comprises a chassis matched with the bottom of the inclusion body and a support bar supporting the four corners of the inclusion body vertically around the chassis. The inner wall of the inclusion body is provided with an aluminum film thermal insulation lining layer, which can be used for high temperature heat preservation and low temperature heat preservation, and the effect is good. One corner of the inclusion body is provided with a cylindrical groove arranged in the inclusion body, the bottom of the groove is provided with a base, and the base is provided with a retractable umbrella handle. The retractable umbrella handle is provided with a sunshade, which can be used as an umbrella when the sun is strong or it rains.
Car enthusiasts are sure to buy dashboard sunshade blankets. The aim is to prevent the dashboard of the vehicle from being seriously exposed to the sun and scratched. But in fact, the car center console is not afraid of exposure. By contrast, cheap sunshade blankets may release toxic gases after exposure. At the same time, there are great security risks.
Internal thermal insulation system when the greenhouse or indoor temperature drops to the set low temperature limit at night, turn off the thermal insulation quilt, strengthen the heat preservation of the greenhouse, design and construction of the solar greenhouse greenhouse, reduce the ground radiation heat loss, reduce the heating energy consumption, and the design and construction of the ecological restaurant, greatly reduce the operating cost of the greenhouse; in the daytime, the shade curtain can be opened, and the design and construction of the multi-span greenhouse greenhouse can make the greenhouse fully daylighting. The working principle is the same as that of internal sunshade, which is made of a lightweight quilt that does not absorb water and weighs between 100 and 150 grams.
Why use sunshade? The main advantage of car shading is to block the sun, so that the light in the action area can not enter the car, to a certain extent, it can reduce the burning inside the car, and prevent leather seats and dashboards from being damaged by ultraviolet rays. Among them, there are many different types of products. Second, in terms of service life, the steel drag chain is generally no less than 10,000 times, which is also a variety of technical advantages that can really be brought about by such a rotation speed. after updating such characteristics, we will be able to constantly grasp such technical characteristics, and then form the key to be more convenient to use in machinery. In order to fully grasp such technical advantages, this is * the main reference. After the continuous improvement of service life, gradually will be in this point of view, or more important, to be able to grasp such a technical advantage, is * the key.